Outdoor WPC Great Wall Fluted Grille Wall Panel
Outdoor WPC Great Wall Fluted Grille Wall Panel

Outdoor WPC Great Wall Fluted Grille Wall Panel

A coordinated outdoor WPC cladding profile with narrow raised rectangular ribs, deep channels, and visible longitudinal hollow cavities for facade, soffit, ceiling, partition, and privacy-screen projects.
Send Inquiry

Specifications

 

Item

Specification

Product Type

Outdoor WPC Great Wall Fluted Grille Panel

Visible Structure

Raised Box Ribs / Recessed Channels / Rectangular Hollow Cavities / Backing Web

Profile Size

On Request

Panel Width

On Request

Panel Length

On Request

Surface Finish

Dark Brown / Gray / Custom Finish On Request

Material Composition

On Request

Installation System

On Request

Application

Facade / Soffit / Outdoor Ceiling / Partition / Privacy Screen

Custom Profile

Available after drawing and sample review

Private Label

Available

Sample Approval

Available

Mixed Container

Available after order review

Packing

On Request

MOQ

500 Square Meter / Each Color or Finish

Production Schedule

On Request

Certification

CE · RoHS

 

Product Introduction

 

A coordinated outdoor WPC cladding profile with narrow raised rectangular ribs, deep channels, and visible longitudinal hollow cavities for facade, soffit, ceiling, partition, and privacy-screen projects.

 

Detailed Description

 

The outdoor WPC Great Wall panel is developed for exterior facade accents, entrance soffits, outdoor ceiling cladding, partitions, privacy screens, and commercial architectural projects that require a regular three-dimensional linear surface. The supplied product image shows coordinated dark-brown and gray wood-grain profiles with narrow raised rectangular ribs, deep recessed channels, longitudinal rectangular hollow cavities, a continuous rear backing web, and side joining edges visible at the cut ends. These visible characteristics create the distinctive Great Wall rhythm while keeping the product identity clearly different from semicircular wave panels or solid decorative boards.

Exact profile size, effective width, overall thickness, panel length, material formulation, surface treatment, installation accessories, packing configuration, and production schedule are On Request. Finish names and availability must be verified against current physical samples. Buyers should not infer fire, structural, acoustic, moisture, ultraviolet, load-bearing, or other performance ratings from product images. Any performance statement requires a supported test report and project-specific technical review.

Exterior project preparation should define wall or soffit dimensions, panel orientation, substrate and support spacing, start and finish points, corner details, joints, openings, drainage clearance, expansion allowance, accessories, and installation sequence. A physical profile and finish sample should be approved before production to confirm color, wood-grain direction, rib spacing, channel depth, cavity geometry, edge appearance, and compatibility with the intended daylight conditions. Digital images support initial selection but do not replace signed samples, approved drawings, or installation planning.

Factory and wholesale services can include profile confirmation, drawing review, cut-to-size preparation, finish matching, private-label packing, sample approval, batch inspection, and mixed-container coordination. The minimum order quantity is 500 Square Meter for each color or finish. CE and RoHS documentation may be supplied where applicable, while supported material or performance reports remain available on request. No additional certification or performance claim is implied.

Before shipment, buyers should confirm the selected profile, finish reference, dimensions, quantity, accessories, carton labels, protection method, pallet plan, and destination requirements. Batch comparison is recommended before installation, especially when several project phases must maintain a coordinated appearance. The outdoor WPC Great Wall panel is positioned as a factory-coordinated decorative cladding solution for distributors, facade contractors, landscape builders, project installers, and commercial buyers requiring profile accuracy, documented approval, and repeatable bulk supply.

 

Ordering Information

 

  • Confirm the selected profile, dimensions, substrate, support spacing, edge details, and accessories against the project drawing.
  • Approve physical profile and finish samples before production.
  • MOQ: 500 Square Meter / Each Color or Finish.
  • Packing and production schedule: On Request.
  • Documentation: CE and RoHS; supported test reports on request.

 

518-detail-1-main

518-detail-2-specification

518-detail-3-application

 

FAQ

Q1. How is it better than real timber?

A: Real timber needs oiling or staining every year, and even then it moves, splits and greys within two or three summers. WPC takes no water, so it cannot rot or feed termites, and the ASA cap holds colour without a coating. Upfront, hardwood costs less per square metre; over ten years the maintenance you avoid usually closes the gap. Where the wall is wet, coastal, shaded or pool-side, timber rarely survives long enough to argue about price.

Q2. Will the colour fade over time?

A: The cap is co-extruded ASA, which is UV-stabilised, so chalking and greying are slow rather than absent. Light greys, creams and woodtones hold best; saturated black, dark walnut and reds shift most because they absorb more solar energy. A south or west facade in a hot climate will show change sooner than a shaded one. Where the design allows, choose a mid or light tone and the difference after years is small.

Q3. How much movement must I allow?

A: WPC moves with temperature, roughly 5 mm at each end on a 2.9 m slat between a cold night and a hot afternoon, so leave that gap and let the clip carry it. Never butt slats hard against a wall, a corner or a starter track. If you fix rigidly through the face, the run has nowhere to go and will bow off the battens in the first heat wave; that is an installation error, not a material fault.

Q4. Can it be fixed straight onto the wall?

A: No. Fix treated battens or an aluminium sub-frame first, then clip the slats so a ventilated cavity of at least 20 mm sits behind them. The cavity lets water drain, lets the wall dry and keeps the profile off a damp surface. Fixed directly, trapped moisture shows up as efflorescence on masonry, blistering on render, and a green film in the shadow of the slat.

Q5. What fire rating does it carry?

A: The standard profile is not rated. On the flame-retardant grade the material reaches B1 to GB 8624, and CE and RoHS documents are supplied with the order. Where the project needs a European classification, tell us the class written in the specification and we confirm what we can support before you price it, rather than after the sample has been approved.

Q6. Is there formaldehyde or VOC?

A: No formaldehyde. The binder is HDPE, a polyolefin, not a urea, melamine or phenolic resin, and the wood flour is encapsulated in the polymer matrix instead of being glued. There is nothing in the profile to off-gas, which is why it is used inside bathrooms, clinics and shopfitting. RoHS documentation is available for buyers who need it on file.

Q7. How is it cleaned, and does it grow mould?

A: Wash with water and a soft brush once or twice a year, and use a mild household detergent where a film has built up. Algae and mildew grow on dirt and pollen sitting on the surface, not inside the material, so a wash removes them and they do not return from within. Avoid solvent cleaners and abrasive pads, which dull the cap, and keep a high-pressure jet away from the profile.

Q8. Can I use it indoors as well?

A: Yes, and this is often why buyers consolidate on one supplier. The same profile runs on bathroom and shower walls, reception features, ceilings, shopfitting and balcony soffits, and thinner indoor sections exist where depth is tight. One colour family then covers inside and outside, so a terrace and the room behind it read as a single scheme.

Q9. Can it be cut, curved or drilled on site?

A: Cut and drill with ordinary woodworking tools and a fine-tooth blade; a mitre saw gives a clean end, and a touch-up pen hides the cut. Gentle bends can be taken over a large radius, but tight curves and returns need a formed corner or a matching trim rather than force. Keep the cut end clear of the ground and seal it where the profile faces driven rain.

Q10. What is the MOQ, lead time and paperwork?

A: 500 square metres per order, with 7 to 30 days production depending on colour and profile, because a non-stock colour needs its own extrusion run. CE and RoHS documents ship with the order, and a cut sample of the actual cap goes out before you commit, so the colour is approved on the real surface. Give us the wall area and profile and we return a quantity with wastage included.

Hot Tags: outdoor wpc great wall fluted grille wall panel, China outdoor wpc great wall fluted grille wall panel manufacturers, suppliers, factory, Outdoor WPC Wall Cladding, wood plastic composite panel width 220mm, WPC Ceiling Panel, WPC Exterior Wall Cladding, WPC Panel Outdoor, WPC Plastic Board