150 Series WPC Bamboo Wood Fiber Fluted Decorative Wall Panel
150 Series WPC Bamboo Wood Fiber Fluted Decorative Wall Panel

150 Series WPC Bamboo Wood Fiber Fluted Decorative Wall Panel

A five-rib hollow decorative wall panel for distributor showrooms, commercial reception areas, retail displays, hospitality interiors and custom project supply.
Send Inquiry

Specifications

 

Item

Specification

Product Type

150 Series Hollow Fluted Decorative Wall Panel

Visible Profile

Five raised ribs with rectangular longitudinal chambers

Surface Finish

Wood Grain / Solid Color

Nominal Series

150

Profile Size

On Request

Panel Width

On Request

Panel Thickness

On Request

Panel Length

On Request

Material Composition

On Request

Installation System

On Request

Application

Interior Decorative Wall Cladding

Cut-to-Size

Available after drawing confirmation

Private Label

Available

Sample Approval

Available

Mixed Container

Available after order review

Packing

On Request

MOQ

500 Square Meter / Each Color or Finish

Production Schedule

On Request

Certification

CE · RoHS

 

Product Introduction

 

A five-rib hollow decorative wall panel for distributor showrooms, commercial reception areas, retail displays, hospitality interiors and custom project supply.

 

Detailed Description

 

The 150 series WPC fluted panel is developed for decorative interior projects that require a repeated linear appearance, varied finish directions and factory-managed order execution. The visible profile uses five raised ribs above rectangular longitudinal cavities and a thin backing web. This geometry creates a clear grille rhythm for distributor showrooms, commercial reception areas, retail displays and hospitality interiors. It is decorative wall cladding rather than structural lumber, and final suitability depends on the approved project drawing and wall condition.

The supplied reference supports wood-grain and multiple solid-color appearances. Exact profile size, usable width, thickness, panel length, material composition, installation system, packing configuration and production schedule are On Request. The number 150 identifies the nominal series stated in the source; it must not be treated as a verified measurement unless confirmed in the final specification sheet. Values from visually similar profiles must not be copied because cavity geometry, rib spacing, backing details and edge conditions may differ.

Project preparation should define panel orientation, start and finish points, corners, joints, openings, accessory requirements and installation sequence. For wood-look finishes, grain direction should be coordinated across adjacent panels. Buyers should approve a physical sample before production to review color, gloss, texture, profile geometry and cut-edge appearance under the intended project lighting. Digital images support initial selection but do not replace the approved sample.

Factory and wholesale services can include drawing review, cut-to-size preparation, finish matching, private-label packing, sample approval, batch inspection and mixed-container planning. The minimum order quantity is 500 Square Meter for each color or finish. CE and RoHS documentation may be supplied where applicable, while supported material or performance reports are available on request. No additional certification claim is implied.

Before shipment, buyers should confirm the profile reference, finish, dimensions, quantity, accessory list, carton labels, protection method and destination requirements. Batch comparison is recommended before installation, especially when several project phases must maintain a coordinated appearance. The 150 series WPC fluted panel is positioned as a factory-coordinated decorative solution for distributors, interior contractors and commercial project buyers requiring custom finishes, documented approval and repeatable bulk supply.

 

Ordering Information

 

• Confirm profile, width, thickness, length and edge details against the approved drawing.

• Approve a physical finish sample before production.

• MOQ: 500 Square Meter / Each Color or Finish.

• Packing and production schedule: On Request.

• Factory service: cut-to-size preparation, private-label packing, mixed-container review and batch inspection.

• Documentation: CE and RoHS; supported test reports on request.

 

504-detail-1-main

504-detail-2-specification

504-detail-3-application

 

FAQ

Q1. How is it better than real timber?

A: Real timber needs oiling or staining every year, and even then it moves, splits and greys within two or three summers. WPC takes no water, so it cannot rot or feed termites, and the ASA cap holds colour without a coating. Upfront, hardwood costs less per square metre; over ten years the maintenance you avoid usually closes the gap. Where the wall is wet, coastal, shaded or pool-side, timber rarely survives long enough to argue about price.

Q2. Will the colour fade over time?

A: The cap is co-extruded ASA, which is UV-stabilised, so chalking and greying are slow rather than absent. Light greys, creams and woodtones hold best; saturated black, dark walnut and reds shift most because they absorb more solar energy. A south or west facade in a hot climate will show change sooner than a shaded one. Where the design allows, choose a mid or light tone and the difference after years is small.

Q3. How much movement must I allow?

A: WPC moves with temperature, roughly 5 mm at each end on a 2.9 m slat between a cold night and a hot afternoon, so leave that gap and let the clip carry it. Never butt slats hard against a wall, a corner or a starter track. If you fix rigidly through the face, the run has nowhere to go and will bow off the battens in the first heat wave; that is an installation error, not a material fault.

Q4. Can it be fixed straight onto the wall?

A: No. Fix treated battens or an aluminium sub-frame first, then clip the slats so a ventilated cavity of at least 20 mm sits behind them. The cavity lets water drain, lets the wall dry and keeps the profile off a damp surface. Fixed directly, trapped moisture shows up as efflorescence on masonry, blistering on render, and a green film in the shadow of the slat.

Q5. What fire rating does it carry?

A: The standard profile is not rated. On the flame-retardant grade the material reaches B1 to GB 8624, and CE and RoHS documents are supplied with the order. Where the project needs a European classification, tell us the class written in the specification and we confirm what we can support before you price it, rather than after the sample has been approved.

Q6. Is there formaldehyde or VOC?

A: No formaldehyde. The binder is HDPE, a polyolefin, not a urea, melamine or phenolic resin, and the wood flour is encapsulated in the polymer matrix instead of being glued. There is nothing in the profile to off-gas, which is why it is used inside bathrooms, clinics and shopfitting. RoHS documentation is available for buyers who need it on file.

Q7. How is it cleaned, and does it grow mould?

A: Wash with water and a soft brush once or twice a year, and use a mild household detergent where a film has built up. Algae and mildew grow on dirt and pollen sitting on the surface, not inside the material, so a wash removes them and they do not return from within. Avoid solvent cleaners and abrasive pads, which dull the cap, and keep a high-pressure jet away from the profile.

Q8. Can I use it indoors as well?

A: Yes, and this is often why buyers consolidate on one supplier. The same profile runs on bathroom and shower walls, reception features, ceilings, shopfitting and balcony soffits, and thinner indoor sections exist where depth is tight. One colour family then covers inside and outside, so a terrace and the room behind it read as a single scheme.

Q9. Can it be cut, curved or drilled on site?

A: Cut and drill with ordinary woodworking tools and a fine-tooth blade; a mitre saw gives a clean end, and a touch-up pen hides the cut. Gentle bends can be taken over a large radius, but tight curves and returns need a formed corner or a matching trim rather than force. Keep the cut end clear of the ground and seal it where the profile faces driven rain.

Q10. What is the MOQ, lead time and paperwork?

A: 500 square metres per order, with 7 to 30 days production depending on colour and profile, because a non-stock colour needs its own extrusion run. CE and RoHS documents ship with the order, and a cut sample of the actual cap goes out before you commit, so the colour is approved on the real surface. Give us the wall area and profile and we return a quantity with wastage included.

Hot Tags: 150 series wpc bamboo wood fiber fluted decorative wall panel, China 150 series wpc bamboo wood fiber fluted decorative wall panel manufacturers, suppliers, factory, Indoor WPC Wall Panel, WPC Color Board, WPC Exterior Wall Panel, wpc panel, WPC panel width 150mm, WPC Wood Slat Panel