Specifications
|
Item |
Specification |
|
Product Type |
Outdoor WPC Fence Board and Slat Collection |
|
Visible Profiles |
Broad Flat Board / Medium Board / Narrow Slat / Grooved Sample / Rail-Like Piece |
|
Board Width |
On Request |
|
Board Thickness |
On Request |
|
Board Length |
On Request |
|
Surface Finish |
Black / Dark Brown / Medium Brown / Light Brown / Custom On Request |
|
Surface Texture |
Wood Grain / Fine Grooves |
|
Material Composition |
On Request |
|
Installation System |
On Request |
|
Application |
Privacy Fence / Garden Boundary / Outdoor Partition / Courtyard Screen |
|
Custom Profile |
Available after drawing and sample review |
|
Private Label |
Available |
|
Sample Approval |
Available |
|
Mixed Container |
Available after order review |
|
Packing |
On Request |
|
MOQ |
500 Square Meter / Each Color or Finish |
|
Production Schedule |
On Request |
|
Certification |
CE · RoHS |
Product Introduction
A coordinated outdoor WPC material collection with broad flat boards, narrow slats, grooved samples, and multiple black-to-brown wood-grain finishes for fence and privacy-screen projects.
Detailed Description
The outdoor WPC fence board collection is developed for commercial privacy fencing, garden boundaries, outdoor partitions, courtyard screening, and landscape projects that require coordinated boards and narrow slats. The supplied reference shows a broad assortment of rectangular products, including wide flat boards, medium-width boards, narrow fence slats, thicker rail-like pieces, and smaller grooved samples. Visible finishes range from black and dark brown to medium and light brown, with smooth wood-grain surfaces and fine linear grooves. These distinctions should be confirmed by physical samples before selection.
Exact board width, thickness, length, material formulation, surface treatment, installation system, support spacing, packing configuration, and production schedule are On Request. The photographs do not confirm whether every profile is solid or hollow, so no hidden cross-section is claimed. Buyers should not infer fire, structural, acoustic, moisture, ultraviolet, load-bearing, or other performance ratings from the images. Any performance statement requires a supported test report and project-specific technical review.
Fence project preparation should define overall length and height, board orientation, post spacing, rail arrangement, gaps, start and finish points, gates, corners, level changes, ground clearance, expansion allowance, fasteners, and installation sequence. A physical board and finish sample should be approved before production to confirm color, wood-grain direction, groove texture, edge appearance, thickness, profile compatibility, and visual response under the intended daylight. Digital images assist initial selection but do not replace approved samples, signed drawings, or installation planning.
Factory and wholesale services can include board and profile confirmation, drawing review, cut-to-size preparation, finish matching, sample approval, batch inspection, private-label packing, and mixed-container coordination. The minimum order quantity is 500 Square Meter for each color or finish. CE and RoHS documentation may be supplied where applicable, while supported material or performance reports remain available on request. No additional certification or performance claim is implied.
Before shipment, buyers should confirm every selected board or slat profile, finish reference, dimensions, quantities, installation accessories, carton labels, protection method, pallet plan, and destination requirements. Batch comparison is recommended before installation, especially where multiple project phases must maintain coordinated color and spacing. The outdoor WPC fence board collection is positioned as a factory-coordinated material range for distributors, fence contractors, landscape builders, project installers, and commercial buyers requiring profile variety, documented sample approval, and repeatable bulk supply.
Ordering Information
- Confirm each board or slat profile, dimensions, post and rail arrangement, gaps, edge details, and installation accessories against the project drawing.
- Approve physical profile and finish samples before production.
- MOQ: 500 Square Meter / Each Color or Finish.
- Packing and production schedule: On Request.
- Documentation: CE and RoHS; supported test reports on request.



FAQ
Q1. How is it better than real timber?
A: Real timber needs oiling or staining every year, and even then it moves, splits and greys within two or three summers. WPC takes no water, so it cannot rot or feed termites, and the ASA cap holds colour without a coating. Upfront, hardwood costs less per square metre; over ten years the maintenance you avoid usually closes the gap. Where the wall is wet, coastal, shaded or pool-side, timber rarely survives long enough to argue about price.
Q2. Will the colour fade over time?
A: The cap is co-extruded ASA, which is UV-stabilised, so chalking and greying are slow rather than absent. Light greys, creams and woodtones hold best; saturated black, dark walnut and reds shift most because they absorb more solar energy. A south or west facade in a hot climate will show change sooner than a shaded one. Where the design allows, choose a mid or light tone and the difference after years is small.
Q3. How much movement must I allow?
A: WPC moves with temperature, roughly 5 mm at each end on a 2.9 m slat between a cold night and a hot afternoon, so leave that gap and let the clip carry it. Never butt slats hard against a wall, a corner or a starter track. If you fix rigidly through the face, the run has nowhere to go and will bow off the battens in the first heat wave; that is an installation error, not a material fault.
Q4. Can it be fixed straight onto the wall?
A: No. Fix treated battens or an aluminium sub-frame first, then clip the slats so a ventilated cavity of at least 20 mm sits behind them. The cavity lets water drain, lets the wall dry and keeps the profile off a damp surface. Fixed directly, trapped moisture shows up as efflorescence on masonry, blistering on render, and a green film in the shadow of the slat.
Q5. What fire rating does it carry?
A: The standard profile is not rated. On the flame-retardant grade the material reaches B1 to GB 8624, and CE and RoHS documents are supplied with the order. Where the project needs a European classification, tell us the class written in the specification and we confirm what we can support before you price it, rather than after the sample has been approved.
Q6. Is there formaldehyde or VOC?
A: No formaldehyde. The binder is HDPE, a polyolefin, not a urea, melamine or phenolic resin, and the wood flour is encapsulated in the polymer matrix instead of being glued. There is nothing in the profile to off-gas, which is why it is used inside bathrooms, clinics and shopfitting. RoHS documentation is available for buyers who need it on file.
Q7. How is it cleaned, and does it grow mould?
A: Wash with water and a soft brush once or twice a year, and use a mild household detergent where a film has built up. Algae and mildew grow on dirt and pollen sitting on the surface, not inside the material, so a wash removes them and they do not return from within. Avoid solvent cleaners and abrasive pads, which dull the cap, and keep a high-pressure jet away from the profile.
Q8. Can I use it indoors as well?
A: Yes, and this is often why buyers consolidate on one supplier. The same profile runs on bathroom and shower walls, reception features, ceilings, shopfitting and balcony soffits, and thinner indoor sections exist where depth is tight. One colour family then covers inside and outside, so a terrace and the room behind it read as a single scheme.
Q9. Can it be cut, curved or drilled on site?
A: Cut and drill with ordinary woodworking tools and a fine-tooth blade; a mitre saw gives a clean end, and a touch-up pen hides the cut. Gentle bends can be taken over a large radius, but tight curves and returns need a formed corner or a matching trim rather than force. Keep the cut end clear of the ground and seal it where the profile faces driven rain.
Q10. What is the MOQ, lead time and paperwork?
A: 500 square metres per order, with 7 to 30 days production depending on colour and profile, because a non-stock colour needs its own extrusion run. CE and RoHS documents ship with the order, and a cut sample of the actual cap goes out before you commit, so the colour is approved on the real surface. Give us the wall area and profile and we return a quantity with wastage included.
Hot Tags: outdoor wpc fence board slat and rail-like profile collection, China outdoor wpc fence board slat and rail-like profile collection manufacturers, suppliers, factory, Wall Panel WPC, wood plastic composite panel solid core option, WPC Exterior Wall Panel, WPC Panel Exterior, WPC Wall Cladding, WPC Wall Panel









